Best sevenoak camera stabilizer to Stabilize Your Camera
Have camera stabilizer for so long, I also put some experience summed up
and share with you, there are some deficiencies in the tutorial, please
entertain friends ~ Part I: Handheld stabilizer adjustment 1, the basic
principle: usually due to Walking people will lead to hand-held objects around
and around, up and down the three directions combined jolt movement. Then, the
hand-held camera stabilizer itself can solve the front and rear and left and right
direction of shaking, here to explain that the hand-held stabilizer does not
"shock", it is to help you in the fulcrum position relative movement so as to
maintain the two directions do not occur Swaying. So when you hold it trot, you
will find that your arms and pace have helped you to cushion the shock, so the
up and down motion damping effect is good or not, directly related to the
operator's ability to operate. Of course, if you have a shock absorber arm,
double damping due to the two springs will be more effective, here, I mainly
talked about the use of handheld Camera stabilizer.
Adjustment steps:
(1) Check: Adjust all the joint buckles to the same straight line, which is beneficial to the balance adjustment of the stabilizer and reduce unnecessary interference factors.
(2) Installed: find the camera or SLR (the following are the camera instead of) the center of gravity position, usually in the center position, and then center the center of the fast plate alignment camera, and then move the screw to the camera screw hole position Tight.
(3) loaded weight: First, we have to estimate the weight of the machine, first weight almost weight loaded up, not enough or too much to do the increase or decrease. Then the universal balance section to move the camera direction, the purpose is to minimize the amount of weight, so that the entire equipment more portable. Then put the main lever level, if the weight side quickly pendulum, indicating too much weight, need to reduce the weight, otherwise increase the weight. Let the weight side free to pendulum, 2 to 3 seconds placed in the vertical line of the subject. Here, I would like to remind everyone that we should try our best to make the main pole shorter, and do not lengthen it unless absolutely necessary because there are two problems involved here: First, too long and too long a force Or the wind can make the stabilizer lose its balance;
Handheld Video Stabilizer SK-SW03N
The Sevenoak stabilizer SK-SW03N is a lightweight, hand-held camera stabilizer system designed for DSLR cameras weighing up to 1.5KG. This system works so well that it allows you to get that incredibly smooth, graceful and steady shot even while going to extremes like running up and down stairs.
Second, each time the machine must be readjusted, very troublesome. Well, the balance of the weight at both ends of the main body after we determine, and then determine how the distribution of weight before and after and about two places, we must first about the weight distribution, in general, do not need to add both sides, you will only see To the camera to the left or right side of the deviation from the vertical line is greater than 20 °, then left or right side to add, until it is less than 20 ° position, add the law is "to the camera side opposite ". Before and after the addition of the weight of the law is the same, do not go into details here! Tips, do not take to adjust the weight balance to add weight.
(4) before and after adjustment and around: I prefer to tune about before
and after the tune. I choose the right and left adjustment knob on my left hand
side as a reference, because this example camera left offset, clockwise
adjustment knob left and right when the camera will move to the right, to the
left and right I want to balance; then adjust the front and rear, open the front
and rear adjustment In this example, the camera leans back, so I have to move
the front and rear adjustment knobs clockwise to move the camera forward until
it reaches the middle position, locking the safety lock. Okay, a few kung fu,
all get.
(5) Fine-tuning: In order to make your stabilizer more stable, you need to spend more time to fine-tune around and before and after transfer to your complete satisfaction!
More information about sevenoak camera slider
camera rigs
Adjustment steps:
(1) Check: Adjust all the joint buckles to the same straight line, which is beneficial to the balance adjustment of the stabilizer and reduce unnecessary interference factors.
(2) Installed: find the camera or SLR (the following are the camera instead of) the center of gravity position, usually in the center position, and then center the center of the fast plate alignment camera, and then move the screw to the camera screw hole position Tight.
(3) loaded weight: First, we have to estimate the weight of the machine, first weight almost weight loaded up, not enough or too much to do the increase or decrease. Then the universal balance section to move the camera direction, the purpose is to minimize the amount of weight, so that the entire equipment more portable. Then put the main lever level, if the weight side quickly pendulum, indicating too much weight, need to reduce the weight, otherwise increase the weight. Let the weight side free to pendulum, 2 to 3 seconds placed in the vertical line of the subject. Here, I would like to remind everyone that we should try our best to make the main pole shorter, and do not lengthen it unless absolutely necessary because there are two problems involved here: First, too long and too long a force Or the wind can make the stabilizer lose its balance;
Handheld Video Stabilizer SK-SW03N
The Sevenoak stabilizer SK-SW03N is a lightweight, hand-held camera stabilizer system designed for DSLR cameras weighing up to 1.5KG. This system works so well that it allows you to get that incredibly smooth, graceful and steady shot even while going to extremes like running up and down stairs.
Second, each time the machine must be readjusted, very troublesome. Well, the balance of the weight at both ends of the main body after we determine, and then determine how the distribution of weight before and after and about two places, we must first about the weight distribution, in general, do not need to add both sides, you will only see To the camera to the left or right side of the deviation from the vertical line is greater than 20 °, then left or right side to add, until it is less than 20 ° position, add the law is "to the camera side opposite ". Before and after the addition of the weight of the law is the same, do not go into details here! Tips, do not take to adjust the weight balance to add weight.
 |
| SEVENOAK CAMERA SLIDER |
(5) Fine-tuning: In order to make your stabilizer more stable, you need to spend more time to fine-tune around and before and after transfer to your complete satisfaction!
More information about sevenoak camera slider
camera rigs
评论
发表评论